Search:

Type: Posts; User: pkennedy

Page 1 of 2 1 2

Search: Search took 0.01 seconds.

  1. Replies
    2
    Views
    215

    I was able to get this to work with help from ifm...

    I was able to get this to work with help from ifm support, just in case anyone else runs into a similar issue.

    I used the RCAN library on the CR1081 and enabled CAN1. (ifmRCAN.CAN_enable)

    I...
  2. Replies
    2
    Views
    215

    CR1081 and CR0401 CANopen connection

    I'm trying to update my CR1081 program from Codesys 2.3 to 3.5, I'm having trouble trying to figure out how to set up the CAN connection between the HMI and PLC. Does anyone have any steps on how to...
  3. Thread: Logging Data

    by pkennedy
    Replies
    8
    Views
    3,830

    Ya I found a company in UK that makes them and...

    Ya I found a company in UK that makes them and ordered one up, Thanks for the info, I haven't started testing the set up yet but hopefully soon.

    Thanks.
  4. Replies
    4
    Views
    2,412

    Have you tried to reset bootloader from the...

    Have you tried to reset bootloader from the standard side? I had issues were CR0232 and CR0032 where the led was red, I contacted ifm support and was able to get warranty for the units with issues.
  5. Thread: Logging Data

    by pkennedy
    Replies
    8
    Views
    3,830

    Hey Ryan, Were you able to get the raspberry...

    Hey Ryan,

    Were you able to get the raspberry pi to work as a data logger for this system? If so did you build a CANbus adapter or purchase one, I have a very similar application and it would be...
  6. Thread: Logging Data

    by pkennedy
    Replies
    8
    Views
    3,830

    I use a CR1081 with an EC2099 to log data however...

    I use a CR1081 with an EC2099 to log data however it's quite a bit more expensive than the CR0452 display (~$2000 difference). We used to have CR3101 which is no longer sold or recommend by ifm.
  7. Replies
    3
    Views
    4,058

    http://www.ifm.com/ifmus/web/ecomatic-download.htm

    http://www.ifm.com/ifmus/web/ecomatic-download.htm
  8. Replies
    2
    Views
    6,949

    How would I be able to determine how much memory...

    How would I be able to determine how much memory the can remote would need for a CR0401 and to determine if I'm currently using too much memory?
  9. Replies
    6
    Views
    5,011

    I uninstalled and reinstalled the maintenance...

    I uninstalled and reinstalled the maintenance tool and changed the port I was connecting my CANFox too and that fixed my issue.
  10. Replies
    2
    Views
    2,767

    I'm fairly new with PLC's so take this...

    I'm fairly new with PLC's so take this information with a grain of salt but have you defined your CAN2? I've had issues where I didn't define CAN2 function block and that prevented me from...
  11. Replies
    6
    Views
    5,011

    SiE MT_API Version 7.4.44.0 When the CANfox is...

    SiE MT_API Version 7.4.44.0

    When the CANfox is connected the information shows up:

    Hardware Type: CANfox(1) CH01
    Firmware: 0x314D
    Serial Number: D3000BBC0000
  12. Replies
    6
    Views
    5,011

    Maintenance Tool and Windows 10

    I'm having issues with Maintenance tool and CANfox, I download the most recent maintenance tool w/ CANfox driver from the ifm website which has windows 10 as a system requirement however after I...
  13. Replies
    5
    Views
    2,842

    Okay sounds good, thanks for your help.

    Okay sounds good, thanks for your help.
  14. Replies
    4
    Views
    4,177

    I don't have any bitmaps only elements, all...

    I don't have any bitmaps only elements, all rectangles and the most is 37. I have it set for 250 and the cycle time were 45000 usec - 52000 usec before connecting to the controller, I didn't have...
  15. Replies
    5
    Views
    2,842

    Ya that's what I was using was just the...

    Ya that's what I was using was just the maintenance tool and download tool.
  16. Replies
    4
    Views
    4,177

    I have 3 screens, screen one shows 5 data values...

    I have 3 screens, screen one shows 5 data values (Press, Temp, Flow Rate, Total Flow, Tank Level), screen 2 shows (Pressure, Temperature, HP, RPM and Tank level) screen 3 shows all 9 values. When I...
  17. Replies
    4
    Views
    4,177

    CR0452 Calculations

    I would like to have variables switch between metric and imperial values, there is approximately 10 values that will need to switch between metric and imperial. It seems if I try to perform the...
  18. Replies
    5
    Views
    2,842

    CR0232 and RS232 Connection

    I'm having issues trying to connect to my controller via RS232, I can connect with can no problems however when I try with RS232 in both downloader and maintenance tool It can't connect.

    I've...
  19. Thread: USB Control

    by pkennedy
    Replies
    3
    Views
    3,184

    I've determined a way however it doesn't use...

    I've determined a way however it doesn't use USB_STORAGE_HANDLER, it uses linux commands with the system_asynch function block with the following command:

    'umount /tmpfs/media/usb/device'

    I was...
  20. Thread: USB Control

    by pkennedy
    Replies
    3
    Views
    3,184

    Anyone have any suggestion?

    Anyone have any suggestion?
  21. Thread: USB Control

    by pkennedy
    Replies
    3
    Views
    3,184

    USB Control

    I'm having issues with a CR1081, I have a USB stick connected directly to the screen and I have the second USB connect using the EC2099.

    Using the USB_STORAGE_HANDLER I'm try on only have one of...
  22. Replies
    1
    Views
    2,465

    The issue was with my Baudrate, I went to...

    The issue was with my Baudrate, I went to Resources > PLC Configuration> CANOPEN Master > CAN parameters and had a baudrate of 125000 for the PLC for CR1081 I had a baudrate of 250000. I changed the...
  23. Replies
    1
    Views
    2,465

    Network Variables

    I'm having issues trying to send network variable from a CR0032 to CR1081. I have the exact same set up with a CR0232 and the variables transfer over with no issues however as soon as I try to use...
  24. Now if it was wired up incorrectly and the wiring...

    Now if it was wired up incorrectly and the wiring is changed would it still be stuck in a fatal error mode? Cause I rewired the unit just to power and ground (pins 10, 19, 32 and 20, 37, 42) along...
  25. What would cause a Fatal Error or Stop with Error on CR0032

    I have a CR0032 which is brand new we had trouble connecting download with RS232 so we used CAN and installed the firmware with Maintenance and CAN. I was able to install the program from Codesys.
    ...
Results 1 to 25 of 28
Page 1 of 2 1 2