Search:

Type: Posts; User: rbenesch

Search: Search took 0.01 seconds.

  1. Replies
    0
    Views
    991

    CAN/J1939 Remote and Transmitter

    Does anyone have any experience or recommendations on a CANbus remote/transmitter combination?

    I currently have an application using the CR2032 and CR0452/482CRM switchbank combination. The...
  2. Replies
    1
    Views
    1,348

    PWM Output on CR2032

    I am new to using the CR2032 and am having some issues configuring an output for PWM.

    Can someone point me in the right direction? In short, I simply need to configure one of the outputs to...
  3. Thread: Logging Data

    by rbenesch
    Replies
    8
    Views
    3,289

    pkennedy - We purchased the CANBus adapter. Just...

    pkennedy - We purchased the CANBus adapter. Just search for PICAN 2 - there are a couple different iterations of it, but it works well and is fairly inexpensive.

    b.koerts - thanks for the info on...
  4. Thread: Logging Data

    by rbenesch
    Replies
    8
    Views
    3,289

    The 451 was added as part of the data logger. My...

    The 451 was added as part of the data logger. My setup consists of the 401 which is transmitting the data points I need over the CAN ID's of my choice to the 451. The 451 is simply there for the...
  5. Replies
    1
    Views
    2,001

    Disregard - A little refresher on my sensors and...

    Disregard - A little refresher on my sensors and wiring and this is working. L+ to my source voltage (VBBS), and L- to my input.
  6. Replies
    1
    Views
    2,001

    PX3111 and CR0401

    When connecting the PX3111 pressure sensor to a CR0401, Pin 1 is L+ and Pin 2 is L-. Can someone explain how with a 2 wire setup this outputs mA? I'm assuming that I need to connect to an input on...
  7. Thread: Logging Data

    by rbenesch
    Replies
    8
    Views
    3,289

    Logging Data

    I've got three analog pressure transmitters, one rotary encoder, and four simple on/off switches connected to a CR0401 that I would like to log the data from.

    I'd like to gather the timestamp and...
  8. Replies
    2
    Views
    2,692

    I figured out a workaround to this. After...

    I figured out a workaround to this.

    After some more testing I determined that the timer was functioning correctly, and even though the output was set to "FALSE" it was still running with the...
  9. Replies
    2
    Views
    2,692

    TON timer to delay output

    I have a TON timer configured to enable an output that is only working once after the initial startup of the controller.

    I have multiple outputs working in conjunction. One output enables the...
  10. Replies
    2
    Views
    1,782

    No power is wired to the CAN line. I do have an...

    No power is wired to the CAN line. I do have an M12 bulkhead that is spliced into everything on N2 but that is only used for connecting into the display\controller after it is installed. I've got...
  11. Replies
    2
    Views
    1,782

    Maximum amps on input

    Is there any information on the maximum amperage that an input could take at 12V before causing issues with the controller (CR0401).

    EDIT
    A bit more information on why I'm asking this. I have an...
  12. Replies
    5
    Views
    2,108

    The CR2032 module is not being used - I am...

    The CR2032 module is not being used - I am guessing that it was setup during the initial project creation for testing purposes and was then left in there once completed.
  13. Replies
    5
    Views
    2,108

    Thanks Erik Confusing is an understatement. ...

    Thanks Erik

    Confusing is an understatement. Would I be better of removing the CANOpen config and switching this back to a Layer 2 template? I'd like to get these configs cleaned up, and it...
  14. Replies
    5
    Views
    2,108

    CANOpen Config Heartbeat Issue

    I'm trying to track down a random communication issue between our CR0401 controller and CR0451 display. I just now getting into the CANOpen portion of this project, and am concerned that this was...
  15. Assign cylinder stroke value from transducer to variables

    I'm trying to walk through a project file and understand how the calibration portion has been configured. We are using the CR0401 controller and CR0451 display. In short, the operator will run...
  16. Replies
    1
    Views
    2,468

    CR0401 Speed Sensor Issue

    I am having an issue with the CR0401 controller and speed sensor on input 0. The sensor posing the problem is a quadrature 600PPR installed in an Eaton H series hydraulic motor. The M12 connector is...
Results 1 to 16 of 16